# I can't upgrade to 1.3

**URL:** <https://community.umbrel.com/t/i-cant-upgrade-to-1-3/20134>\
**Category:** Support and Troubleshooting\
**Created:** [November 26, 2024, 1:33pm UTC](https://community.umbrel.com/t/i-cant-upgrade-to-1-3/20134 "2024-11-26T13:33:35Z")\
**Posts on this page:** 1\
**Showing post:** 29

<div class="post-metadata">

**Author:** ![yeliaB](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.umbrel.com/yeliab/32/3652_2.png) [@yeliaB](https://community.umbrel.com/u/yeliaB)\
**Post date:** [December 5, 2024, 7:20pm UTC](https://community.umbrel.com/t/i-cant-upgrade-to-1-3/20134/29 "2024-12-05T19:20:13Z")

</div>

Okay, got a rpi4 that is experiencing the same issue:

1. I start the update.
2. I watch the progress bar.
3. As the progress bar reaches the end, I see a couple of buttons on the screen for a fraction of a second, and then I’m brought back to the login screen before I can even do anything.
4. I login and find I’m still running 1.2.2, and I’m told there’s an update available.
5. I reboot and find I’m still running 1.2.2, and I’m told there’s an update available.

Looking through the forum, I found the instructions about how to bring up a terminal and enter the following command:

`sudo mender install https://download.umbrel.com/release/1.3.0/umbrelos-pi.update && sudo rugpi-ctrl system reboot --spare`

After entering the command, everything seemed to be going okay until the following happened:

```auto
INFO[0038] Output (stdout) from command "/usr/share/mender/modules/v3/rugpi-image": Found 3,system-a kind: 0x83, start: 1064960, size: 7143136 
............................................................. - 99 %ERRO[0497] Download failed: Unable to open /var/lib/mender/modules/v3/payloads/0000/tree/stream-next: open /var/lib/mender/modules/v3/payloads/0000/tree/stream-next: no such file or directory 
INFO[0497] Could not access /var/lib/mender/modules/v3/payloads/0000/tree, assuming cleanup already done: stat /var/lib/mender/modules/v3/payloads/0000/tree: no such file or directory 
ERRO[0497] Unable to open /var/lib/mender/modules/v3/payloads/0000/tree/stream-next: open /var/lib/mender/modules/v3/payloads/0000/tree/stream-next: no such file or directory

```

I looked into `/var/lib/mender/modules/v3/payloads/0000/` and sure enough there’s nothing other than `.` and `..` in there.

I then did an fdisk -l and saw no errors and got the following summary at the end:

```auto
Disk /dev/mmcblk0: 29.72 GiB, 31914983424 bytes, 62333952 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0xa2fecfe6

Device Boot Start End Sectors Size Id Type
/dev/mmcblk0p1 8192 532479 524288 256M c W95 FAT32 (LBA)
/dev/mmcblk0p2 532480 794623 262144 128M c W95 FAT32 (LBA)
/dev/mmcblk0p3 794624 1056767 262144 128M c W95 FAT32 (LBA)
/dev/mmcblk0p4 1056768 62333951 61277184 29.2G 5 Extended
/dev/mmcblk0p5 1064960 11550719 10485760 5G 83 Linux
/dev/mmcblk0p6 11558912 22044671 10485760 5G 83 Linux
/dev/mmcblk0p7 22052864 62333951 40281088 19.2G 83 Linux

Disk /dev/sda: 1.82 TiB, 2000398934016 bytes, 3907029168 sectors
Disk model: 500SSD1         
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: gpt
Disk identifier: 0EB9FA04-1F84-40C4-81DE-6BDB7B6A8594

Device Start End Sectors Size Type
/dev/sda1 2048 3907028991 3907026944 1.8T Linux filesystem

```

I’m open to any suggestions about how to proceed from here…

---

_[View the full topic](https://community.umbrel.com/t/i-cant-upgrade-to-1-3/20134)._